| Field | Description |
|---|
| Type
|
Specify which of the following types of labels you are printing addresses on:
- Avery 5160 (three labels across on a standard 8.5" x 11" page)
- Avery 5161 (two labels across on a standard 8.5" x 11" page)
- Avery L7163 (two labels across on a standard 8.26" x 11.69" A4 page)
- User-defined (any other label format)
When you select a type of label,
GovWin Capture Management sets the other options in the
Print Setup section to default measurements.
If you select one of the standard types of labels, print a test page to check the alignment of the information on the labels. If the alignment is not correct, change the default measurements.
If you select
User-defined, take the required measurements from a sheet of labels and enter them in the
Print Setup section.
If you make any changes to the default settings or if you enter settings for a user-defined label, save the new measurements as a set of saved options or as a favorite, so you do not have to adjust the alignment the next time you print labels.
|
| Top Margin
|
Enter the distance from the top of the page to the top of the first row of labels.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
If you use inches, enter decimals for fractions. For example, enter
.500 for a margin of one-half inch.
|
| Left Margin
|
Enter the distance from the left edge of the page to the left edge of the first column of labels.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
If you use inches, enter decimals for fractions. For example, enter
.125 for a margin of one-eighth inch.
|
| Vertical Gap
|
Enter the distance between the bottom of one row of labels and the top of the next row.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
Enter
0.000 if there is no gap.
|
| Horizontal Gap
|
Enter the distance between the right edge of one column of labels and the left edge of the next column.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
If you use inches, enter decimals for fractions. For example, enter
.125 for a gap of one-eighth inch.
Enter
0.000 if there is no gap.
|
| Label Height
|
Enter the distance from the top edge of a label to its bottom edge.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
For example, if you use inches, enter
1.000 for a label that is one inch high.
|
| Label Width
|
Enter the distance from the left edge of a label to its right edge.
Use the unit of measure (inches or millimeters) that you entered in the
Unit of Measure field on this tab.
For example, if you use inches, enter
4.000 for a label that is four inches wide.
|
| Number Across
|
Enter the number of labels in each row.
|
| Number Down
|
Enter the number of rows of labels on each page.
|
| Orientation
|
Select one of the following options for the orientation of the page of labels:
|
| Page Size
|
From the drop-down list, select the mailing label page size.
The width and height of the page size that you select in this field display in the
Page Width and
Page Height fields below the
Page Size field.
When you select the
Custom size, the
Width and
Height fields are enabled so you can enter a width and height of your choice.
|
| Page Width and Page Height
|
The
Page Width and
Page Height fields display the width and height of the page size that you select in the
Page Size field.
The measurements display in either inches or millimeters based on which one you selected in the
Unit of Measure field on this tab.
|
| Unit of Measure
|
From the drop-down list, select the unit of measure, inches or millimeters, to use for the measurement fields under
Print Setup on this tab.
When you switch from one unit of measure to the other, the measurements that are currently entered or displayed in the measurement field are automatically converted to the new unit of measure.
(1 inch = 25.4 millimeter)
|
| Font Name
|
Select the font for the mailing labels.
The font that prefills in this field is the default font that you selected on the Reporting tab of the User Options dialog box.
|
| Font Size
|
Select the font size (type size) for the mailing labels.
|
| Company
|
Select this check box to include the lead's company on the mailing labels.
|
| Title
|
Select this check box to include the lead's title on the mailing labels.
|
